The Worlds Biggest (and Best!) Nail Knowledge Centre

Curing UV Nail Gel

The Complexity of Curing UV Nail Gels

19 Views

I’ve noticed that many nail technicians tend to oversimplify the UV curing process for nail coatings and this has created misunderstandings. In my opinion, UV cured nail coatings are the most technically sophisticated and complex products in the beauty industry.  Many underestimate the various aspects of UV curing, including nail lamps. They don’t appreciate how many factors influence cure and instead oversimplify everything, including “wattage”, which is not as important as most believe. In fact, if you buy a lamp just because of its wattage, you are likely to be disappointed.

There are three types of cure for UV nail coatings

The three cures are an under-cure, over-cure and proper cure. Here is some information that you need to know to achieve a “proper cure” and avoid the other possibilities. Curing is NOT about the wattage. Don’t be fooled by those who just want to sell you a nail lamp. Wattage is “power consumption” and not “UV output”. The second mistake that some make is to focus on the range of wavelengths emitted by their UV bulbs, however, that is not enough and is only another part of all that must be considered to ensure a UV gel properly cures.

UV-GEL hand in nail lamp

 What’s Needed for Proper UV Curing?

 In my scientific opinion, the best way is to ensure a proper cure is to consistently apply a thin layer of UV gel with the correct thickness and then cure that thin layer for the proper length of time, using a nail lamp that emits the correct UV wavelengths needed to efficiently activate the photoinitiators in the UV gel. Also, those wavelengths can have neither too high nor too low of intensity for the UV curing product. Too high of an intensity causes over-curing; too low of an intensity causes under-curing.

The design of the nail lamp is important

Besides the wavelength and intensity, even the DESIGN of the lamp is very important. For instance, the distance between the nail plates and the bulbs makes a very big difference in curing. Very small changes in this distance can have big consequences on curing. Most people don’t think about the electronics inside the lamp. The electronic components drive the bulbs to create UV. These components influence UV intensity and different lamps have different components. If the exact same UV bulbs are used in two different brands of UV nail lamps, the bulbs can produce widely different UV intensities. It’s important to note that old UV bulbs should be replaced with the same type and model of the UV bulb. Fluorescent style bulbs should generally be changed 2-4 times per year depending on how often the nail lamps are used.

 Too few understand how important the design of the nail lamp is in curing. The positioning of the bulbs and even the type of interior reflector material used are VERY important factors that influence curing. This is why it is wrong to assume that only wattage is important when it is the least important of these factors. The most confusing of all is that many are fooled when UV products harden. They incorrectly assume that hardening means properly cured, but in many cases, it is not. UV nail coatings will harden when they cure more than 50%. However, to obtain the best properties and avoid causing skin sensitivities, these coatings should be cured to around 90%. So, there are many clients walking around with under cured enhancements, which are more prone to service breakdown and more likely to cause adverse skin reactions, especially for nail technicians who are repeatedly exposed to partially cured UV gel dust and filings.

The information above applies ONLY to MMA monomer. Powders containing MMA should really be called PMMA (poly methyl methacrylate). PMMA has completely different chemical structure/properties and is considered safe for use in artificial nails. PMMA in a sheet form is called Plexiglas™ and Lucite™.

How do I know this information is correct?

I have spent many years developing some of the leading UV nail products in the world and am also one of the top scientific experts on UV nail lamps. These are the facts as I know them. This information is important because too many nail professionals don’t realize that many of their service breakdown problems are probably due to improper cures.

Improper cure can cause everything from cracking, breaking, shattering, lifting, pitting, discoloration, bubbles, and onycholysis to adverse skin reactions. In my opinion, improper curing is a leading cause of skin sensitivity, producing symptoms such as skin redness, itching, water blisters, etc. These are completely avoidable and would not happen if these coatings were properly applied and cured. In short, don’t use a UV nail lamp (either LED or fluorescent style) unless it is recommended by the UV curing product manufacturers and then always cure these products exactly as directed.

en_GBEnglish
Shopping Cart